Try TT Now

Preparing to Install

Customer Tasks

Before the BVMF Gateway is installed, the customer must perform the following tasks:

  • Obtain the host server IP addresses, associated passwords, and connection ports. BM&FBOVESPA (BVMF) distributes this information in a separate document (or E-mail). You must obtain one set of connection information for each Order Router or customer membership that uses the BVMF Gateway. The Firm ID is publicly available and can be obtained from your brokerage firm or the BVMF website.
  • For circuit sizing (network bandwidth) between your network and the BVMF host, refer to the BVMF specifications.
  • Confirm that all network routes to BVMF work from the server onto which TT plans to install the BVMF Gateway.
  • Obtain the IP address that BVMF defines for your TT Gateway. You must use this IP address as either the NATed address if you are using a NAT firewall, or the address of the NIC (Network Interface Card) that faces the BVMF network if you are using a dual-homed server.
  • For each connection to the exchange, obtain the SessionId from BVMF.
  • The following are customer tasks specific to networking and network setup:

    • BVMF distributes its UMDF price feeds via multicast traffic to a network area that you define for BVMF.
    • For history data requests, you must enable TCP connections on the TT Gateway.
    • The IP address and subnet mask that you send to BVMF for the Price Server UMDF connection should be that of the local LAN facing NIC on the BVMF Gateway.
    • When setting up IP addresses, you must ensure that they are fully resolved through any NAT firewalls and NAT routers that are used.
      Warning

      TT does not support or recommend using NAT IP addresses to connect to the exchange. BVMF holds you fully responsible for all maintenance regarding NAT IP addresses. You must consult the exchange for all NAT implementation details.

    • On all network devices that reside between the BVMF Gateway and the BVMF host network, you must ensure that the Exchange ports used in the hostinfo.cfg file are available for one-way, outbound TCP sessions to the BVMF host servers.
    • Obtain network connectivity information from BVMF for the remote host IP addresses and ports to which the BVMF Gateway must connect, and the names of the customer-side routers.

Installer Tasks

Note

You must observe the following when installing a BVMF Gateway:

  • When performing any of the BVMF Gateway installation tasks, you must be logged into the gateway server as an Administrator.
  • Procedures and tasks presented in this manual supplement the information stored in the TT Gateway Architecture SAM Version 7.X.

As the installer, you must perform the following tasks before installing the BVMF Gateway:

  • If you have TT products of Version 7.X already installed on the network, you must obtain the aconfig.xml file from one of the machines that hosts the 7.X software. This can be from any 7.X machine on your network.
  • Identify the products to which the customer’s memberships want to subscribe. You must add this information to the [PriceServer] section of the hostinfo.cfg file. Refer to Configuring Product Subscriptions .
  • If the BVMF Gateway uses multiple NIC cards, identify the IP address of each NIC that faces the exchange’s network.
  • Obtain all membership connection information for memberships that use the BVMF Gateway. BVMF distributes these values to their customers. Refer to for a list of all needed values.

Installation Requirements

TT Gateway 7.16 and higher

TT Gateways 7.16 and higher fully support the Window Server 2008 R2 64-bit operating system.

Note

Window Server 2008 R2 64-bit is the only version of Windows Server 2008 supported by TT.

You can also install TT Gateways 7.16 on machines running Windows Server 2003.

TT Gateways 7.15 and lower

You can install TT Gateways 7.15.x or lower on machines running Windows Server 2003.

In addition, you can install the following TT Gateways on a machine running Windows Server 2008 R2 Service Pack 1:

  • TT Montreal, CBOE and FIX Gateways 7.13
  • All TT Gateways 7.14 and 7.15

Prior to installing 7.15 or lower on Windows Server 2008, you must be aware of the following caveats and required changes:

  • Migrating to Windows Server 2008: TT does not support upgrading the operating system on an existing TT Gateway server. TT strongly suggests that users perform a clean install of the operating system and the TT Gateway when migrating to Windows Server 2008.
  • Program Files directory: Windows Server 2008 does not allow applications to create files under the Program Files directory.

    If during a command line installation of the TT Gateway, you place the install root in the Program Files directory, you must select a different location for the ttconfig, ttdatfiles and ttlogfiles directories by using the installconfig, installdata and installlog arguments.

  • Event Viewer Errors: Certain TT applications may trigger minor Event Viewer error messages. These errors do not impact gateway behavior. However, users can avoid triggering these messages by starting the Windows Interactive Services Detection prior to install.
  • Console Windows: By default, some console windows triggered by TT Gateways may not display and instead produce an Interactive Service Detection dialog box. Users may run the Interactive Services Detection and switch over to the Windows “Session 0” desktop to view messages displayed from server.
  • Starting Programs: TT Chron may not properly close and/or monitor server programs that are started manually. Users should first start TT Chron and allow it to start the server program per its schedule.
  • Start TT Chron desktop icon: The “Start TT Chron” desktop shortcut may not work unless the user right-clicks on the icon and select “Run as administrator” from the context menu.
  • TTM_BASE_API error: An issue exists where TTM may trigger a TTM_BASE_API error message in the Event Viewer. This is a known issue with TTM and does not impact gateway behavior.
  • User Account Control: You must disable the Windows User Account Control for the TT Gateways to properly function. The User Account Control prevents the gateway from updating files including changes to the aconfig.xml file and updates to the product table.